Building a Guinea Pig Pen

Pen 1 & 2 together

Last Summer I undertook the challenge of making a proper indoor guinea pig pen for our two girls (Peanut Butter) Oreo & (Princess) Tink (Tinkerbell, the Diva).  Below is a step by step guide on how this was done.  I did it in two parts as it was quite a big job.  

Unfortunately I am unhappy at the size of pen 2 so I will be expanding on this soon.  I will however post pen 2 up as the whole design was made to suit easy expansion so there will be a pen 2 expansion guide later as well.

The cost of this cage was absolutely zero as it was all re-used wood form an old wardrobe, aquarium sealer was left over from a previous project and screws were there already too.

What tools did I need to make this cage?

Drill, sander, Aquarium silicon to seal the pen, Screwdriver, hammer, screws, PVA Glue to help strengthen the joints, dowels to help strengthen the base and back joint. and the following:

The above was Pen 1, made specifically to fill with hay and keep the hay inside the pen as much as possible.  

Step 1:  Cut the base (measurements are 50 cm depth x 100 cm Length. 

Step 2; Cut out the back (46cm x 100cm

Step 3: cut out the two side panels and label A and B 44.5cm x 48.5 cm each (this accounts for the thickness of the base and back of the pen.  

Step 4 take side panel B (the closest to where pen B is going to be) and cut a large arch so as the guinea pigs can get back and forth form pen 2

Step 5: cut a front panel out (depending on wood thickness – this is 15mm each) 97cm long x 20 cm high

Step 6: Cut a panel for the roof of the cage approx. 15 cm x 98.5cm

Step 7: Line up the side panels with the front and top panels and mark a diagonal line to match and line up with each one.  keep it as flush as possible.  (I did calculate the measure for mine, but I don’t have the precise calculations and measurements to hand anymore and this is a good way of measuring it as well. 

Here are some photos of the process as it moves along:

Pen 1

Pen 2

Once it was all screwed together, I used aquarium sealer around the inside edges to stop water leakage.  I then put cup hooks into the top front of each side panel and hung a wire mesh panel on it to help the piggy’s feel more secure as they were not keen on the openness of the pen. 

Viola! Pen 1 complete.  If, however, you make this with a non-veneered wood you will have to find a nontoxic way of sealing the wood surface.  this was all made form an old wardrobe, so it was veneered MDF.  Easy to cut and work with and completely waterproof on the surface.   I also added ‘feet’ to the pen to raise it off the floor allowing air to circulate under the pen. 

Pen 1 with temporary attachment

I hope this helps and is clear enough, if however, you have any questions please feel free to use the comments below to ask.  Pen 2 will be uploaded shortly.  The best thing about this method of building was that I could keep the original pen attached to this pen until I had time to build the second pen. 

Fudge's New Habitat

So we all decided that Fudge seemed a bit bored in his Hamster Heaven (HH).  He had taken to constantly seeping and hardly getting up through the night to play.  Myself and my fiancé were getting a bit worried about him so we thought it would be a good idea to build him a bigger habitat to live in and oh boy is it bigger ! Fudge has gone from his HH which gives him 4.3  square feet  to his DIY habitat which gives him 6.2 square feet of roaming floor space.  He had a good investigate of this space and seems to have found himself a beautiful dark little corner to sleep in, the HH was to bright and he always ended up sleeping in the light as he didn't seem to like any other house we put in there for him.

I have put this guide up to show that it doesn't have to cost a fortune to make your own cage as this only cost me £25 for extra wood for the mesh cover and supports, the mesh and hinges and handles.  I also bought face masks as I was sawing MDF veneered wood and safety goggles as I was using a Jigsaw.

Fudges new habitat started off as a plain old TV unit

Firstly I took the top off of the unit so as I could add hinged lids and a mesh lid later, and also let me remove the two dividers inside the unit.

I took one the dividers and cut an arch into it using the Jigsaw and re-attached about a cm further away from its original place as I needed to fit 3 detolf shelves in the large gap.

I then cut and attached some old table legs to help hold the glass in place from the exterior of the cage

I then added the 3 detolf shelves in the front and some support wood on the inside (top and bottom) to hold it. I used aquarium sealer to seal the shelves together and to the sides of the wood.

I cut two pieces of wood from an old wardrobe and added the handles (about £2.00 each) this is the first cost in the building of this cage as I had old wood and screws spare from old furniture and previous cage builds.

I then attached a hinge to each lid (should have been 2 but I mis-judged the weight of each lid. these where about £3.50 for 2 hinges. (There is a mesh covered hole in the top, please ignore as this was not part of the design - It was the last piece of wood suitable for a lid ha ha).

I added a support beam to the outside of the habitat to help support the weight of lid number 2 and made a wire mesh lid for the end lid

I then added a mesh window in the hideaway section to let air get in. the mesh and the wood used to make the mesh totalled to around £15 altogether

I would recommend adding the shelf before putting the glass in but I did it the hard way Ha ha. Add wood shavings/aspen, and hay, and of course, toys.

I hope this helps anyone wanting to build their own habitat for their Hamsters but am more than happy to answer any questions.